After running on Spike simulator, seL4 can now run on the latest up-to-date version of Rocket Chip code on FPGA, the first hardware platform that seL4/RISC-V port can run on. Moreover, seL4 runs on the online jor1k emulator . This can be considered as a starting point for both RISC-V and seL4 to experiment some new security-related and/or scalability solutions based on the flexibility to easily modify the hardware according to seL4 requirements (or vice versa), given that both are open-source, and under research development.
Previously seL4/RISC-V was only running on RV32 (RISC-V 32-bit mode) which assumes SV32 (Page-Based 32-bit Virtual-Memory Systems) to work on. SV32 was only supported by Spike simulator, and that's why seL4 could, previously, only run there. The 32-bit seL4 has been progressing till the point that it is able to run, not only a hello world application, but it can run another simple operating system above it  that can fork other applications. That seems to be a good progress, but it would be better to have it running on a real hardware.
The issue was that the only open-source RISC-V hardware is currently Rocket Chip, which doesn't support 32-bit (SV32) mode, only RV64 (SV39 and SV48 virtual memory systems that run only on RISC-V 64-bit mode), and since there's no 64-bit support on seL4 (yet), it would have been hard and time-consuming to re-factor the entire seL4 code to run 64-bit code (including pointers, variables, data structures, scripts, etc).
How does 32-bit seL4 run on RV64/SV39?
The workaround was to keep running 32-bit seL4, but with modifications to the RISC-V low-level target-dependent MMU handling code to run on RV64/SV39 memory system without touching the target-independent seL4 code. This was possible because both RV32 and RV64 execute 32-bit fixed instructions. So basically, only the memory configuration was required (apart from HTIF code) to be modified to make this step possible, including initialization and page-tables layout. This means that seL4 is still being built and compiled using riscv32-* toolchain.
The seL4 components that had to be changed are:
vspace.c is an architecture-dependent core file (for all seL4 ports) for MMU handling in seL4 microkernel. A new file, vspace64.c was added to run on RV64 mode. The difference between the 32-bit version is that the 4KiB pages should now follow 3 levels page-tables implementation instead of just 2 levels (SV32).
elfloader is just statically mapping the seL4 microkernel image at 2-level page-table, 2MiB pages granularity, while it maps seL4 at 4MiB granularity (just one level page-table) on SV32
RV32/SV32 implementation of seL4 can cover 4GiB address space, while RV64/SV39 extends this to 2^9 GiB. seL4 port only uses 256 MiB, so this amount of SV39 memory wasn't needed. This made it simpler by using only two entries in the first-level page-table: one for the first GiB (reserved for applications use), and the second one for the kernel page-tables. The first-level page-table (AKA page-directory) is then shared between all applications, but write accesses is only exclusive to seL4 microkernel. New applications (address spaces) are just allocating/filling 2nd-level (and if necessary 3rd-level to provide 4KiB pages) page-tables without worrying about the first level. During context switches, address space change is done by writing the address of the second-level page table (allocated by applications) into the first entry of the page-directory rather than updating the sptbr register. This solution has a limitation of restricting application address space mapping to the first GiB virtual address range, but it has the benefit of optimizing both memory and time. Memory optimization is achieved by the fact that there is no need to allocate 3-level page-tables when creating a new task, only two (or even one) as with SV32. From timing perspective, seL4 is copying the kernel mapping for each created task, this is no longer needed since this kernel mapping lies on a separate 2nd entry, covering the 256 MiB of the second GiB virtual memory of the page directory. The SV39 mapping of seL4 is shown in the next figure.
Next, I will be working on cleaning up the code, writing some tutorials how to build and run seL4 on different RISC-V platforms, fixing bugs and adding more features.